Gai-tronics VoIP Telephone Software Configuration Guide Manual de usuario descargar pdf (Pagina 64)

GAI-TRONICS

VoIP Telephone Configuration Guide Page 64 of 88

Section Item Identifier Value(s) Comments

REGISTRAR

xxx.xxx.xxx.xxx

or FQDN

This command sets the address of the Registrar to be

xxx.xxx.xxx.xxx or the FQDN specified. The registrar

address and the proxy may or may not be the same

address, but the address for registration must be set

here.

REGISTRARPO

XXXX

The port to send the register to.

USERNAME “username”

This command sets the username for the

authorisation realm to be username ( Default value is

blank)

PASSWORD “password”

This command sets the password for the

authorisation realm to be password ( Default value is

blank)

ENDPOINT [ENABLED | DISABLED] Sets whether this set of proxy parameters is active.

SMTP

SERVER1

xxx.xxx.xxx.xxx

FQDN

Sets the IP address of the primary SMTP server to be

xxx.xxx.xxx.xxx or uses the FQDN to resolve the IP

address through DNS. Email will be sent on assertion

of an alarm condition via the primary server if

configured.

SERVER2

xxx.xxx.xxx.xxx

FQDN

Sets the IP address of the secondary SMTP server to

be xxx.xxx.xxx.xxx or uses the FQDN to resolve the

IP address through DNS. Email will be sent on

assertion of an alarm condition via the secondary

server if configured.

TOADDRESS [email protected]om Sets the To: Address

CCADDRESS [email protected]om Sets the CC: Address

FROMADDRESS [email protected] Sets the FROM: Address

SUBJECT “SubjectText”

Set the contents of the subject field to be

“SubjectText”. The Subject Text field can be up to 50

characters in length, and can contain any printable

character except double quotes.

SMTP [ON|OFF]

This setting enables or disables the use of SMTP

within the unit.

TONES

[TONE1 –TONE10]

FREQ 1-13

These commands set the various call tones produced

by the telephone.

See Tone Settings web page section (5.15) for

detailed explanation.

For example to set a standard UK and US ring tones

the commands would be:

ON1

0-600 (*25ms)

OFF1

ON2 UK US

OFF2

TONE3=FREQ 5

TONE3=ON1 0

TONE3=OFF1 0

TONE3=ON2 16

TONE3=OFF2 8

TONE3=ON3 16

TONE3=OFF3 80

TONE3=FREQ 3

TONE3=ON1 0

TONE3=OFF1 0

TONE3=ON2 80

TONE3=OFF2 160

TONE3=ON3 0

TONE3=OFF3 0

ON3

OFF3

UNIT

HOSTNAME xxxxxxxx

Sets the unit host name for this unit to be

XXXXXXXXXXXX where X is any alphanumeric

character. Maximum of 15 characters. Default Value

is "UNNAMED”.

UPDATE SERVER

xxx.xxx.xxx.xx

FQDN

Sets the IP address of the host running the TFTP

server to be xxx.xxx.xxx.xxx or resolves the FQDN

using DNS to access the host containing the update

file(s).

UPDATE FILE Filename

The name of the file on the TFTP server. This name

may contain the macro symbols %m, %h and %i.

These symbols are expanded to the MAC address,

host name and IP address respectively.

UPDATE INTERVAL X

This command forces the unit to attempt a

configuration file download every X hours where X

can be an integer value between 0 and 1000. A value

of 0 disables the periodic update request. The default

value is 1. Any non-zero value will cause the unit to

attempt a configuration file download at boot time.

HELPSERVER

xx.xxx.xxx.xxx

FQDN

Sets the address for the Web Support Page link on

the Home page.

LAN SPEED AUTO|10|100 Ethernet speed

3XED

1 2 ... 59 60 61 62 63 64 65 66 67 68 69 ... 87 88

Comentarios a estos manuales

Sin comentarios

Gai-tronics VoIP Telephone Software Configuration Guide Manual de usuario Pagina 64

Comentarios a estos manuales

Relacionado con productos y manuales para Comunicación Gai-tronics VoIP Telephone Software Configuration Guide